✨ More fan kickstarts

MarlinFirmware/Marlin#26581
MarlinFirmware · Dec 29, 2023 · 16b7191 · 16b7191
1 parent 1de2f3b
commit 16b7191
Show file tree

Hide file tree

Showing 354 changed files with 4,945 additions and 2,823 deletions.
diff --git a/config/default/Configuration_adv.h b/config/default/Configuration_adv.h
@@ -584,6 +584,9 @@
   #define CONTROLLERFAN_SPEED_IDLE        0 // (0-255) Idle speed, used when motors are disabled
   #define CONTROLLERFAN_IDLE_TIME        60 // (seconds) Extra time to keep the fan running after disabling motors
 
+  //#define CONTROLLERFAN_KICKSTART_TIME  100  // (ms)
+  //#define CONTROLLERFAN_KICKSTART_POWER 180  // 64-255
+
   // Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
   //#define CONTROLLER_FAN_MIN_BOARD_TEMP 40  // (°C) Turn on the fan if the board reaches this temperature
 
@@ -602,8 +605,8 @@
  * gets it spinning reliably for a short time before setting the requested speed.
  * (Does not work on Sanguinololu with FAN_SOFT_PWM.)
  */
-//#define FAN_KICKSTART_TIME  100  // (ms)
-//#define FAN_KICKSTART_POWER 180  // 64-255
+//#define EFAN_KICKSTART_TIME  100  // (ms)
+//#define EFAN_KICKSTART_POWER 180  // 64-255
 
 // Some coolers may require a non-zero "off" state.
 //#define FAN_OFF_PWM  1
@@ -692,12 +695,15 @@
 #define CHAMBER_AUTO_FAN_PIN -1
 #define COOLER_AUTO_FAN_PIN -1
 
-#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
-#define EXTRUDER_AUTO_FAN_SPEED 255   // 255 == full speed
-#define CHAMBER_AUTO_FAN_TEMPERATURE 30
-#define CHAMBER_AUTO_FAN_SPEED 255
-#define COOLER_AUTO_FAN_TEMPERATURE 18
-#define COOLER_AUTO_FAN_SPEED 255
+#define EXTRUDER_AUTO_FAN_TEMPERATURE        50
+#define EXTRUDER_AUTO_FAN_SPEED             255  // 255 is full speed
+//#define EXTRUDER_AUTO_FAN_KICKSTART_TIME  100  // (ms)
+//#define EXTRUDER_AUTO_FAN_KICKSTART_POWER 180  // 64-255
+
+#define CHAMBER_AUTO_FAN_TEMPERATURE   28
+#define CHAMBER_AUTO_FAN_SPEED        255
+#define COOLER_AUTO_FAN_TEMPERATURE    18
+#define COOLER_AUTO_FAN_SPEED         255
 
 /**
  * Hotend Cooling Fans tachometers

diff --git a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h
@@ -584,6 +584,9 @@
   #define CONTROLLERFAN_SPEED_IDLE        0 // (0-255) Idle speed, used when motors are disabled
   #define CONTROLLERFAN_IDLE_TIME        60 // (seconds) Extra time to keep the fan running after disabling motors
 
+  //#define CONTROLLERFAN_KICKSTART_TIME  100  // (ms)
+  //#define CONTROLLERFAN_KICKSTART_POWER 180  // 64-255
+
   // Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
   //#define CONTROLLER_FAN_MIN_BOARD_TEMP 40  // (°C) Turn on the fan if the board reaches this temperature
 
@@ -602,8 +605,8 @@
  * gets it spinning reliably for a short time before setting the requested speed.
  * (Does not work on Sanguinololu with FAN_SOFT_PWM.)
  */
-//#define FAN_KICKSTART_TIME  100  // (ms)
-//#define FAN_KICKSTART_POWER 180  // 64-255
+//#define EFAN_KICKSTART_TIME  100  // (ms)
+//#define EFAN_KICKSTART_POWER 180  // 64-255
 
 // Some coolers may require a non-zero "off" state.
 //#define FAN_OFF_PWM  1
@@ -692,12 +695,15 @@
 #define CHAMBER_AUTO_FAN_PIN -1
 #define COOLER_AUTO_FAN_PIN -1
 
-#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
-#define EXTRUDER_AUTO_FAN_SPEED 255   // 255 == full speed
-#define CHAMBER_AUTO_FAN_TEMPERATURE 30
-#define CHAMBER_AUTO_FAN_SPEED 255
-#define COOLER_AUTO_FAN_TEMPERATURE 18
-#define COOLER_AUTO_FAN_SPEED 255
+#define EXTRUDER_AUTO_FAN_TEMPERATURE        50
+#define EXTRUDER_AUTO_FAN_SPEED             255  // 255 is full speed
+//#define EXTRUDER_AUTO_FAN_KICKSTART_TIME  100  // (ms)
+//#define EXTRUDER_AUTO_FAN_KICKSTART_POWER 180  // 64-255
+
+#define CHAMBER_AUTO_FAN_TEMPERATURE   28
+#define CHAMBER_AUTO_FAN_SPEED        255
+#define COOLER_AUTO_FAN_TEMPERATURE    18
+#define COOLER_AUTO_FAN_SPEED         255
 
 /**
  * Hotend Cooling Fans tachometers

diff --git a/config/examples/ADIMLab/Gantry v1/Configuration_adv.h b/config/examples/ADIMLab/Gantry v1/Configuration_adv.h
@@ -584,6 +584,9 @@
   #define CONTROLLERFAN_SPEED_IDLE        0 // (0-255) Idle speed, used when motors are disabled
   #define CONTROLLERFAN_IDLE_TIME        60 // (seconds) Extra time to keep the fan running after disabling motors
 
+  //#define CONTROLLERFAN_KICKSTART_TIME  100  // (ms)
+  //#define CONTROLLERFAN_KICKSTART_POWER 180  // 64-255
+
   // Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
   //#define CONTROLLER_FAN_MIN_BOARD_TEMP 40  // (°C) Turn on the fan if the board reaches this temperature
 
@@ -602,8 +605,8 @@
  * gets it spinning reliably for a short time before setting the requested speed.
  * (Does not work on Sanguinololu with FAN_SOFT_PWM.)
  */
-//#define FAN_KICKSTART_TIME  100  // (ms)
-//#define FAN_KICKSTART_POWER 180  // 64-255
+//#define EFAN_KICKSTART_TIME  100  // (ms)
+//#define EFAN_KICKSTART_POWER 180  // 64-255
 
 // Some coolers may require a non-zero "off" state.
 //#define FAN_OFF_PWM  1
@@ -692,12 +695,15 @@
 #define CHAMBER_AUTO_FAN_PIN -1
 #define COOLER_AUTO_FAN_PIN -1
 
-#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
-#define EXTRUDER_AUTO_FAN_SPEED 255   // 255 == full speed
-#define CHAMBER_AUTO_FAN_TEMPERATURE 30
-#define CHAMBER_AUTO_FAN_SPEED 255
-#define COOLER_AUTO_FAN_TEMPERATURE 18
-#define COOLER_AUTO_FAN_SPEED 255
+#define EXTRUDER_AUTO_FAN_TEMPERATURE        50
+#define EXTRUDER_AUTO_FAN_SPEED             255  // 255 is full speed
+//#define EXTRUDER_AUTO_FAN_KICKSTART_TIME  100  // (ms)
+//#define EXTRUDER_AUTO_FAN_KICKSTART_POWER 180  // 64-255
+
+#define CHAMBER_AUTO_FAN_TEMPERATURE   28
+#define CHAMBER_AUTO_FAN_SPEED        255
+#define COOLER_AUTO_FAN_TEMPERATURE    18
+#define COOLER_AUTO_FAN_SPEED         255
 
 /**
  * Hotend Cooling Fans tachometers

diff --git a/config/examples/ADIMLab/Gantry v2/Configuration_adv.h b/config/examples/ADIMLab/Gantry v2/Configuration_adv.h
@@ -584,6 +584,9 @@
   #define CONTROLLERFAN_SPEED_IDLE        0 // (0-255) Idle speed, used when motors are disabled
   #define CONTROLLERFAN_IDLE_TIME        60 // (seconds) Extra time to keep the fan running after disabling motors
 
+  //#define CONTROLLERFAN_KICKSTART_TIME  100  // (ms)
+  //#define CONTROLLERFAN_KICKSTART_POWER 180  // 64-255
+
   // Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
   //#define CONTROLLER_FAN_MIN_BOARD_TEMP 40  // (°C) Turn on the fan if the board reaches this temperature
 
@@ -602,8 +605,8 @@
  * gets it spinning reliably for a short time before setting the requested speed.
  * (Does not work on Sanguinololu with FAN_SOFT_PWM.)
  */
-//#define FAN_KICKSTART_TIME  100  // (ms)
-//#define FAN_KICKSTART_POWER 180  // 64-255
+//#define EFAN_KICKSTART_TIME  100  // (ms)
+//#define EFAN_KICKSTART_POWER 180  // 64-255
 
 // Some coolers may require a non-zero "off" state.
 //#define FAN_OFF_PWM  1
@@ -692,12 +695,15 @@
 #define CHAMBER_AUTO_FAN_PIN -1
 #define COOLER_AUTO_FAN_PIN -1
 
-#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
-#define EXTRUDER_AUTO_FAN_SPEED 255   // 255 == full speed
-#define CHAMBER_AUTO_FAN_TEMPERATURE 30
-#define CHAMBER_AUTO_FAN_SPEED 255
-#define COOLER_AUTO_FAN_TEMPERATURE 18
-#define COOLER_AUTO_FAN_SPEED 255
+#define EXTRUDER_AUTO_FAN_TEMPERATURE        50
+#define EXTRUDER_AUTO_FAN_SPEED             255  // 255 is full speed
+//#define EXTRUDER_AUTO_FAN_KICKSTART_TIME  100  // (ms)
+//#define EXTRUDER_AUTO_FAN_KICKSTART_POWER 180  // 64-255
+
+#define CHAMBER_AUTO_FAN_TEMPERATURE   28
+#define CHAMBER_AUTO_FAN_SPEED        255
+#define COOLER_AUTO_FAN_TEMPERATURE    18
+#define COOLER_AUTO_FAN_SPEED         255
 
 /**
  * Hotend Cooling Fans tachometers

diff --git a/config/examples/Alfawise/U20-bltouch/Configuration_adv.h b/config/examples/Alfawise/U20-bltouch/Configuration_adv.h
@@ -584,6 +584,9 @@
   #define CONTROLLERFAN_SPEED_IDLE        0 // (0-255) Idle speed, used when motors are disabled
   #define CONTROLLERFAN_IDLE_TIME        60 // (seconds) Extra time to keep the fan running after disabling motors
 
+  //#define CONTROLLERFAN_KICKSTART_TIME  100  // (ms)
+  //#define CONTROLLERFAN_KICKSTART_POWER 180  // 64-255
+
   // Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
   //#define CONTROLLER_FAN_MIN_BOARD_TEMP 40  // (°C) Turn on the fan if the board reaches this temperature
 
@@ -602,8 +605,8 @@
  * gets it spinning reliably for a short time before setting the requested speed.
  * (Does not work on Sanguinololu with FAN_SOFT_PWM.)
  */
-//#define FAN_KICKSTART_TIME  100  // (ms)
-//#define FAN_KICKSTART_POWER 180  // 64-255
+//#define EFAN_KICKSTART_TIME  100  // (ms)
+//#define EFAN_KICKSTART_POWER 180  // 64-255
 
 // Some coolers may require a non-zero "off" state.
 //#define FAN_OFF_PWM  1
@@ -692,12 +695,15 @@
 #define CHAMBER_AUTO_FAN_PIN -1
 #define COOLER_AUTO_FAN_PIN -1
 
-#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
-#define EXTRUDER_AUTO_FAN_SPEED 255   // 255 == full speed
-#define CHAMBER_AUTO_FAN_TEMPERATURE 30
-#define CHAMBER_AUTO_FAN_SPEED 255
-#define COOLER_AUTO_FAN_TEMPERATURE 18
-#define COOLER_AUTO_FAN_SPEED 255
+#define EXTRUDER_AUTO_FAN_TEMPERATURE        50
+#define EXTRUDER_AUTO_FAN_SPEED             255  // 255 is full speed
+//#define EXTRUDER_AUTO_FAN_KICKSTART_TIME  100  // (ms)
+//#define EXTRUDER_AUTO_FAN_KICKSTART_POWER 180  // 64-255
+
+#define CHAMBER_AUTO_FAN_TEMPERATURE   28
+#define CHAMBER_AUTO_FAN_SPEED        255
+#define COOLER_AUTO_FAN_TEMPERATURE    18
+#define COOLER_AUTO_FAN_SPEED         255
 
 /**
  * Hotend Cooling Fans tachometers

diff --git a/config/examples/Alfawise/U20/Configuration_adv.h b/config/examples/Alfawise/U20/Configuration_adv.h
@@ -584,6 +584,9 @@
   #define CONTROLLERFAN_SPEED_IDLE        0 // (0-255) Idle speed, used when motors are disabled
   #define CONTROLLERFAN_IDLE_TIME        60 // (seconds) Extra time to keep the fan running after disabling motors
 
+  //#define CONTROLLERFAN_KICKSTART_TIME  100  // (ms)
+  //#define CONTROLLERFAN_KICKSTART_POWER 180  // 64-255
+
   // Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
   //#define CONTROLLER_FAN_MIN_BOARD_TEMP 40  // (°C) Turn on the fan if the board reaches this temperature
 
@@ -602,8 +605,8 @@
  * gets it spinning reliably for a short time before setting the requested speed.
  * (Does not work on Sanguinololu with FAN_SOFT_PWM.)
  */
-//#define FAN_KICKSTART_TIME  100  // (ms)
-//#define FAN_KICKSTART_POWER 180  // 64-255
+//#define EFAN_KICKSTART_TIME  100  // (ms)
+//#define EFAN_KICKSTART_POWER 180  // 64-255
 
 // Some coolers may require a non-zero "off" state.
 //#define FAN_OFF_PWM  1
@@ -692,12 +695,15 @@
 #define CHAMBER_AUTO_FAN_PIN -1
 #define COOLER_AUTO_FAN_PIN -1
 
-#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
-#define EXTRUDER_AUTO_FAN_SPEED 255   // 255 == full speed
-#define CHAMBER_AUTO_FAN_TEMPERATURE 30
-#define CHAMBER_AUTO_FAN_SPEED 255
-#define COOLER_AUTO_FAN_TEMPERATURE 18
-#define COOLER_AUTO_FAN_SPEED 255
+#define EXTRUDER_AUTO_FAN_TEMPERATURE        50
+#define EXTRUDER_AUTO_FAN_SPEED             255  // 255 is full speed
+//#define EXTRUDER_AUTO_FAN_KICKSTART_TIME  100  // (ms)
+//#define EXTRUDER_AUTO_FAN_KICKSTART_POWER 180  // 64-255
+
+#define CHAMBER_AUTO_FAN_TEMPERATURE   28
+#define CHAMBER_AUTO_FAN_SPEED        255
+#define COOLER_AUTO_FAN_TEMPERATURE    18
+#define COOLER_AUTO_FAN_SPEED         255
 
 /**
  * Hotend Cooling Fans tachometers

diff --git a/config/examples/AliExpress/CL-260/Configuration_adv.h b/config/examples/AliExpress/CL-260/Configuration_adv.h
@@ -584,6 +584,9 @@
   #define CONTROLLERFAN_SPEED_IDLE        0 // (0-255) Idle speed, used when motors are disabled
   #define CONTROLLERFAN_IDLE_TIME        60 // (seconds) Extra time to keep the fan running after disabling motors
 
+  //#define CONTROLLERFAN_KICKSTART_TIME  100  // (ms)
+  //#define CONTROLLERFAN_KICKSTART_POWER 180  // 64-255
+
   // Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
   //#define CONTROLLER_FAN_MIN_BOARD_TEMP 40  // (°C) Turn on the fan if the board reaches this temperature
 
@@ -602,8 +605,8 @@
  * gets it spinning reliably for a short time before setting the requested speed.
  * (Does not work on Sanguinololu with FAN_SOFT_PWM.)
  */
-//#define FAN_KICKSTART_TIME  100  // (ms)
-//#define FAN_KICKSTART_POWER 180  // 64-255
+//#define EFAN_KICKSTART_TIME  100  // (ms)
+//#define EFAN_KICKSTART_POWER 180  // 64-255
 
 // Some coolers may require a non-zero "off" state.
 //#define FAN_OFF_PWM  1
@@ -692,12 +695,15 @@
 #define CHAMBER_AUTO_FAN_PIN -1
 #define COOLER_AUTO_FAN_PIN -1
 
-#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
-#define EXTRUDER_AUTO_FAN_SPEED 255   // 255 == full speed
-#define CHAMBER_AUTO_FAN_TEMPERATURE 30
-#define CHAMBER_AUTO_FAN_SPEED 255
-#define COOLER_AUTO_FAN_TEMPERATURE 18
-#define COOLER_AUTO_FAN_SPEED 255
+#define EXTRUDER_AUTO_FAN_TEMPERATURE        50
+#define EXTRUDER_AUTO_FAN_SPEED             255  // 255 is full speed
+//#define EXTRUDER_AUTO_FAN_KICKSTART_TIME  100  // (ms)
+//#define EXTRUDER_AUTO_FAN_KICKSTART_POWER 180  // 64-255
+
+#define CHAMBER_AUTO_FAN_TEMPERATURE   28
+#define CHAMBER_AUTO_FAN_SPEED        255
+#define COOLER_AUTO_FAN_TEMPERATURE    18
+#define COOLER_AUTO_FAN_SPEED         255
 
 /**
  * Hotend Cooling Fans tachometers

diff --git a/config/examples/AliExpress/UM2pExt/Configuration_adv.h b/config/examples/AliExpress/UM2pExt/Configuration_adv.h
@@ -584,6 +584,9 @@
   #define CONTROLLERFAN_SPEED_IDLE        0 // (0-255) Idle speed, used when motors are disabled
   #define CONTROLLERFAN_IDLE_TIME        60 // (seconds) Extra time to keep the fan running after disabling motors
 
+  //#define CONTROLLERFAN_KICKSTART_TIME  100  // (ms)
+  //#define CONTROLLERFAN_KICKSTART_POWER 180  // 64-255
+
   // Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
   //#define CONTROLLER_FAN_MIN_BOARD_TEMP 40  // (°C) Turn on the fan if the board reaches this temperature
 
@@ -602,8 +605,8 @@
  * gets it spinning reliably for a short time before setting the requested speed.
  * (Does not work on Sanguinololu with FAN_SOFT_PWM.)
  */
-#define FAN_KICKSTART_TIME    100  // (ms)
-//#define FAN_KICKSTART_POWER 180  // 64-255
+#define EFAN_KICKSTART_TIME    100  // (ms)
+//#define EFAN_KICKSTART_POWER 180  // 64-255
 
 // Some coolers may require a non-zero "off" state.
 //#define FAN_OFF_PWM  1
@@ -692,12 +695,15 @@
 #define CHAMBER_AUTO_FAN_PIN -1
 #define COOLER_AUTO_FAN_PIN -1
 
-#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
-#define EXTRUDER_AUTO_FAN_SPEED 255   // 255 == full speed
-#define CHAMBER_AUTO_FAN_TEMPERATURE 30
-#define CHAMBER_AUTO_FAN_SPEED 255
-#define COOLER_AUTO_FAN_TEMPERATURE 18
-#define COOLER_AUTO_FAN_SPEED 255
+#define EXTRUDER_AUTO_FAN_TEMPERATURE        50
+#define EXTRUDER_AUTO_FAN_SPEED             255  // 255 is full speed
+//#define EXTRUDER_AUTO_FAN_KICKSTART_TIME  100  // (ms)
+//#define EXTRUDER_AUTO_FAN_KICKSTART_POWER 180  // 64-255
+
+#define CHAMBER_AUTO_FAN_TEMPERATURE   28
+#define CHAMBER_AUTO_FAN_SPEED        255
+#define COOLER_AUTO_FAN_TEMPERATURE    18
+#define COOLER_AUTO_FAN_SPEED         255
 
 /**
  * Hotend Cooling Fans tachometers

diff --git a/config/examples/Anet/A2/Configuration_adv.h b/config/examples/Anet/A2/Configuration_adv.h
@@ -584,6 +584,9 @@
   #define CONTROLLERFAN_SPEED_IDLE        0 // (0-255) Idle speed, used when motors are disabled
   #define CONTROLLERFAN_IDLE_TIME        60 // (seconds) Extra time to keep the fan running after disabling motors
 
+  //#define CONTROLLERFAN_KICKSTART_TIME  100  // (ms)
+  //#define CONTROLLERFAN_KICKSTART_POWER 180  // 64-255
+
   // Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
   //#define CONTROLLER_FAN_MIN_BOARD_TEMP 40  // (°C) Turn on the fan if the board reaches this temperature
 
@@ -602,8 +605,8 @@
  * gets it spinning reliably for a short time before setting the requested speed.
  * (Does not work on Sanguinololu with FAN_SOFT_PWM.)
  */
-//#define FAN_KICKSTART_TIME  100  // (ms)
-//#define FAN_KICKSTART_POWER 180  // 64-255
+//#define EFAN_KICKSTART_TIME  100  // (ms)
+//#define EFAN_KICKSTART_POWER 180  // 64-255
 
 // Some coolers may require a non-zero "off" state.
 //#define FAN_OFF_PWM  1
@@ -692,12 +695,15 @@
 #define CHAMBER_AUTO_FAN_PIN -1
 #define COOLER_AUTO_FAN_PIN -1
 
-#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
-#define EXTRUDER_AUTO_FAN_SPEED 255   // 255 == full speed
-#define CHAMBER_AUTO_FAN_TEMPERATURE 30
-#define CHAMBER_AUTO_FAN_SPEED 255
-#define COOLER_AUTO_FAN_TEMPERATURE 18
-#define COOLER_AUTO_FAN_SPEED 255
+#define EXTRUDER_AUTO_FAN_TEMPERATURE        50
+#define EXTRUDER_AUTO_FAN_SPEED             255  // 255 is full speed
+//#define EXTRUDER_AUTO_FAN_KICKSTART_TIME  100  // (ms)
+//#define EXTRUDER_AUTO_FAN_KICKSTART_POWER 180  // 64-255
+
+#define CHAMBER_AUTO_FAN_TEMPERATURE   28
+#define CHAMBER_AUTO_FAN_SPEED        255
+#define COOLER_AUTO_FAN_TEMPERATURE    18
+#define COOLER_AUTO_FAN_SPEED         255
 
 /**
  * Hotend Cooling Fans tachometers